|
ISO 15000 - ISO 20000 +
ISO 15001:2003
Anaesthetic and respiratory equipment. Compatibility with oxygen
ISO 15004:1998
Ophthalmic instruments. Fundamental requirements and test methods
ISO 15005:2002
Road vehicles. Ergonomic aspects of transport information and control systems. Dialogue management principles and compliance procedures
ISO 15007-1:2002
Road vehicles. Measurement of driver visual behaviour with respect to transport information and control systems. Definitions and parameters
ISO 15008:2003
Road vehicles. Ergonomic aspects of transport information and control systems. Specifications and compliance procedures for in-vehicle visual presentation
ISO 15009:2002
Soil quality. Gas chromatographic determination of the content of volatile aromatic hydrocarbons, naphthalene and volatile halogenated hydrocarbons. Purge-and-trap method with thermal desorption
ISO 15010:1998
Disposable hanging devices for transfusion and infusion bottles. Requirements and test methods
ISO 15011-1:2002
Health and safety in welding and allied processes. Laboratory method for sampling fume and gases generated by arc welding. Determination of emission rate and sampling for analysis of particulate fume
ISO 15011-2:2003
Health and safety in welding and allied processes. Laboratory method for sampling fume and gases generated by arc welding. Determination of emission rates of gases, except ozone
ISO 15011-3:2002
Health and safety in welding and allied processes. Laboratory method for sampling fume and gases generated by arc welding. Determination of ozone concentration using fixed point measurements
ISO 15013:1999
Extruded sheets of polypropylene (PP). Requirements and test methods
ISO 15016:2002
Ships and marine technology. Guidelines for the assessment of speed and power performance by analysis of speed trial data
ISO 15022-1:1999
Securities. Scheme for messages (data field dictionary). Data field and message design rules and guidelines
ISO 15022-2:1999
Securities. Scheme for messages (data field dictionary). Maintenance of the data field dictionary and catalogue of messages
ISO 15023-1:2001
Plastics. Poly(vinyl alcohol) (PVAL) materials. Designation system and basis for specifications
ISO 15023-2:2003
Plastics. Poly(vinyl alcohol) (PVAL) materials. Determination of properties
ISO 15024:2001
Fibre-reinforced plastic composites. Determination of mode I interlaminar fracture toughness, $iG$di$dc, for unidirectionally reinforced materials
ISO 15025:2002
Protective clothing. Protection against heat and flame. Method of test for limited flame spread
ISO/IEC 15026:1998
Information technology. System and software integrity levels
ISO 15027-1:2002
Immersion suits. Constant wear suits, requirements including safety
ISO 15027-2:2002
Immersion suits. Abandonment suits, requirements including safety
ISO 15027-3:2002
Immersion suits. Test methods
ISO 15029-1:2000
Petroleum and related products. Determination of spray ignition characteristics of fire-resistant fluids. Spray flame persistence. Hollow-cone nozzle method
ISO 15032:2000
Prostheses. Structural testing of hip joints
ISO 15033:2000
Plastics. Determination of caprolactam and its cyclic and linear oligomers by HPLC
ISO 15034:2000
Composites. Prepregs. Determination of resin flow
ISO 15037-1:1998
Road vehicles. Vehicle dynamics test methods. General conditions for passenger cars
ISO 15037-2:2002
Road vehicles. Vehicle dynamics test methods. General conditions for heavy vehicles and buses
ISO 15038:1999
Plastics. Organic-perester crosslinking agents for unsaturated-polyester thermosetting materials. Determination of active-oxygen content
ISO 15040:1999
Composites. Prepregs. Determination of gel time
ISO 15061:2001
Water quality. Determination of dissolved bromate. Method by liquid chromatography of ions
ISO/IEC 15068-2:1999
Information technology. Portable operating system interface (POSIX) system administration. Software administration
ISO TR 15069:1997
Series 1 freight containers. Handling and securing. Rationale for ISO 3874 annex A
ISO TR 15070:1996
Series 1 freight containers. Rationale for structural test criteria
ISO 15072:1999
Hexagon bolts with flange with metric fine pitch thread. Small series. Product grade A
ISO 15078:1998
Machinery for forestry. Log loaders. Location and method of operation of two-lever operator controls
ISO 15083:2003
Small craft. Bilge-pumping systems
ISO 15084:2003
Small craft. Anchoring, mooring and towing. Strong points
ISO 15085:2003
Small craft. Man-overboard prevention and recovery
ISO 15086-1:2001
Hydraulic fluid power. Determination of fluid-borne noise characteristics of components and systems. Hydraulic fluid power. Determination of the fluid borne noise characteristics of components and systems. Introduction
ISO 15086-2:2000
Hydraulic fluid power. Determination of fluid-borne noise characteristics of components and systems. Measurement of speed of sound in a fluid in a pipe
ISO 15087-1:2001
Dental elevators. General requirements
ISO 15087-2:2000
Dental elevators. Warwick James elevators
ISO 15087-3:2000
Dental elevators. Cryer elevators
ISO 15087-4:2000
Dental elevators. Coupland elevators
ISO 15087-5:2000
Dental elevators. Bein elevators
ISO 15087-6:2000
Dental elevators. Flohr elevators
ISO 15098-1:2001
Dental tweezers. General requirements
ISO 15098-2:2000
Dental tweezers. Meriam types
ISO 15098-3:2000
Dental tweezers. College types
ISO 15100:2000
Plastics. Reinforcement fibres. Chopped strands. Determination of bulk density
ISO 15105-1:2002
Plastics. Film and sheeting. Determination of gas-transmission rate. Differential-pressure method
ISO 15105-2:2003
Plastics. Film and sheeting. Determination of gas-transmission rate. Equal-pressure method
ISO 15113:1999
Rubber. Determination of frictional properties
ISO/IEC ISP 15122-2:1999
Information technology. International standardized profiles AOM3nn. OSI management. AOM312. Lower layer systems and network management ensemble for TB/TC/TD/TE/RB/RC/profiles
ISP 15124-1:1999
Information technology. International standardized profile FOD126. Open document format: image applications. Enhanced document structure. Character, raster graphics, and geometric graphics content architecture. Document application profile (DAP)
ISO/IEC ISP 15125-7:1998
Information technology. International Standardized Profiles ADYnn. OSI Directory. ADY43. DSA to DSA authentication
ISO 15136-1:2001
Downhole equipment for petroleum and natural gas industries. Progressing cavity pump systems for artificial lift. Pumps
ISO 15138:2001
Petroleum and natural gas industries. Offshore production installations. Heating, ventilation and air-conditioning
ISO 15141-1:1998
Foodstuffs. Determination of ochratoxin A in cereals and cereal products. High performance liquid chromatographic method with silica gel clean up
ISO 15141-2:1998
Foodstuffs. Determination of ochratoxin A in cereals and cereal products. High performance liquid chromatographic method with bicarbonate clean up
ISO 15142-1:2003
Implants for surgery. Metal intramedullary nailing systems. Intramedullary nails
ISO 15142-2:2003
Implants for surgery. Metal intramedullary nailing systems. Locking components
ISO 15142-3:2003
Implants for surgery. Metal intramedullary nailing systems. Connection devices and reamer diameter measurements
ISO/IEC 15145:1997
Information technology. Programming languages. FORTH
ISO 15147:1999
Light conveyor belts. Tolerances on widths and lengths of cut light conveyor belts
ISO 15148:2002
Hygrothermal performance of building materials and products. Determination of water absorption coefficient by partial immersion
ISO 15152:2003
Tobacco. Determination of the content of total alkaloids as nicotine. Continuous-flow analysis method
ISO 15153:2003
Tobacco. Determination of the content of reducing substances. Continuous-flow analysis method
ISO 15154:2003
Tobacco. Determination of the content of reducing carbohydrates. Continuous-flow analysis method
ISO 15156-1:2002
Petroleum and natural gas industries. Materials for use in H$d2S-containing environments in oil and gas production. General principles for selection of cracking-resistant materials
ISO 15161:2001
Guidelines on the application of ISO 9001:2000 for the food and drink industry
ISO 15166-1:1998
Adhesives. Methods of preparing bulk specimens. Two-part systems
ISO 15166-2:2000
Adhesives. Methods of preparing bulk specimens. Elevated-temperature-curing one-part systems
ISO 15171-1:1999
Connections for fluid power and general use. Hydraulic couplings for diagnostic purposes. Coupling not for connection under pressure
ISO 15171-2:2000
Connections for fluid power and general use. Hydraulic couplings for diagnostic purposes. Coupling with M16 x 2 end for connection under pressure
ISO 15176:2002
Soil quality. Characterization of excavated soil and other soil materials intended for re-use
ISO 15186-1:2000
Acoustics. Measurement of sound insulation in buildings and of building elements using sound intensity. Laboratory conditions
ISO 15186-2:2003
Acoustics. Measurement of sound insulation in buildings and of building elements using sound intensity. Field measurements
ISO 15186-3:2002
Acoustics. Measurement of sound insulation in buildings and of building elements using sound intensity. Laboratory measurements at low frequencies
ISO 15188:2001
Project management guidelines for terminology standardization
ISO 15189:2003
Medical laboratories. Particular requirements for quality and competence
ISO 15197:2003
$7IIn vitro$7R diagnostic test systems. Requirements for blood-glucose monitoring systems for self-testing in managing diabetes mellitus
ISO/IEC 15200:1996
Information technology. Adaptive lossless data compression algorithm (ALDC)
ISO 15202-1:2000
Workplace air. Determination of metals and metalloids in airborne particulate matter by inductively coupled plasma atomic emission spectrometry. Sampling
ISO 15212-1:1999
Oscillation-type density meters. Laboratory instruments
ISO 15212-2:2002
Oscillation-type density meters. Process instruments for homogenous liquids
ISO 15213:2003
Microbiology of food and animal feeding stuffs. Horizontal method for the enumeration of sulfite-reducing bacteria growing under anaerobic conditions
ISO 15214:1998
Microbiology of food and animal feeding stuffs. Horizontal method for the enumeration of mesophilic lactic acid bacteria. Colony-count technique at 30$0DC
ISO 15217:2000
Fluid power systems and components. 16mm square electrical connector with earth contact. Characteristics and requirements
ISO 15218:2003
Pneumatic fluid power. 3/2 solenoid valves. Mounting interface surfaces
ISO 15225:2000
Nomenclature. Specification for a nomenclature system for medical devices for the purpose of regulatory data exchange
ISO 15227:2000
Optics and optical instruments. Microscopes. Testing of stereomicroscopes
DD ISO/TR 15235:2001
Preparation of steel substrates before application of paints and related products. Collected information on the effect of levels of water-soluble salt contamination
ISO 15241:2001
Rolling bearings. Symbols for quantities
ISO 15245-1:2001
Gas cylinders. Parallel threads for connection of valves to gas cylinders. Specification
ISO 15245-2:2001
Gas cylinders. Parallel threads for connection of valves to gas cylinders. Gauge inspection
ISO 15252-1:2000
Plastics. Epoxy powder moulding compounds (EP-PMCs). Designation system and basis for specifications
ISO 15252-2:2000
Plastics. Epoxy powder moulding compounds (EP-PMCs). Preparation of test specimens and determination of properties
ISO 15252-3:2000
Plastics. Epoxy powder moulding compounds (EP-PMCs). Requirements for selected moulding compounds
ISO 15253:2000
Ophthalmic optics and instruments. Optical devices for low-vision aids
ISO 15254:2002
Ophthalmic optics and instruments. Electro-optical devices for enhancing low vision
ISO/IEC TR 15271:1998
Information technology. Guide for ISO/IEC 12207. (Software life cycle processes)
ISO/IEC TR 15285:1998
Information technology. An operational model for characters and glyphs
ISO/IEC ISP 15287-2:2000
Information technology. Standardized application environment profile. Posix Realtime Application Support (AEP)
ISO/IEC 15288:2002
Systems engineering. System life cycle processes
ISO/IEC 15292:2001
Information technology. Security techniques. Protection profile registration procedures
ISO/IEC TR 15294:2000
Information technology. Methods for data flow control at synchronous and asynchronous DTE-DCE interfaces
ISO 15301:2001
Animal and vegetable fats and oils. Determination of sediment in crude fats and oils. Centrifuge method
ISO 15303:2001
Animal and vegetable fats and oils. Detection and identification of a volatile organic contaminent by GC/MS
ISO 15304:2002
Animal and vegetable fats and oils. Determination of the content of trans fatty acid isomers of vegetable fats and oil. Gas chromatographic method
ISO 15310:1999
Reinforced plastics. Determination of the in-plane shear modulus by the plate twist method
ISO 15318:2000
Pulp, paper and board. Determination of 7 specified polychlorinated biphenyls (PCB)
ISO 15319:1999
Recycled pulps. Estimation of visible contraries by instrumental means using reflected light
ISO 15323:2002
Dried milk protein products. Determination of nitrogen solubility index
ISO 15324:2000
Corrosion of metals and alloys. Evaluation of stress corrosion cracking by the drop evaporation test
ISO 15330:1999
Fasteners. Preloading test for the detection of hydrogen embrittlement. Parallel bearing surface method
ISO 15348:2002
Pipework. Metal bellows expansion joints. General
ISO 15349-2:2003
Unalloyed steel. Determination of low carbon content. Infrared absorption method after combustion in an induction furnace (with preheating)
ISO 15350:2001
Steel and iron. Determination of total carbon and sulfur content. Infrared absorption method after combustion in an induction furnace (routine method)
ISO 15359:1999
Paper and board. Determination of the static and kinetic coefficients of friction. Horizontal plane method
ISO 15360-1:2000
Recycled pulps. Estimation of stickies and plastics. Visual method
ISO 15361:2000
Pulps. Determination of zero-span tensile strength, wet or dry
ISO 15364:2002
Ships and marine technology. Pressure/vacuum valves for cargo tanks
ISO 15368:2001
Optics and optical instruments. Measurement of reflectance of plane surfaces and transmittance of plane parallel elements
ISO 15371:2000
Ships and marine technology. Fire-extinguishing systems for protection of galley deep-fat cooking equipment. Fire tests
ISO 15372:2000
Ships and marine technology. Inflatable rescue boats. Coated fabrics for inflatable chambers
ISO 15373:2001
Plastics. Polymer dispersions. Determination of free formaldehyde
ISO 15374:1998
Implants for surgery. Requirements for production of forgings
ISO TR 15377:1998
Measurement of fluid flow by means of pressure differential devices. Guidelines for specification of nozzles and orifice plates beyond the scope of ISO 5167-1
ISO 15380:2002
Lubricants, industrial oils and related products (class L). Family H (hydraulic systems). Specifications for categories HETG, HEPG, HEES and HEPR
ISO 15394:2000
Packaging. Bar code and two-dimensional symbols for shipping, transport and receiving labels
ISO 15401:2000
Ships and marine technology. Bulk carriers. Construction quality of hull structure
ISO 15402:2000
Ships and marine technology. Bulk carriers. Repair quality of hull structure
ISO 15403:2000
Natural gas. Designation of the quality of natural gas for use as a compressed fuel for vehicles
ISO 15407-1:2000
Pneumatic fluid power. Five-port directional control valves, sizes 18 mm and 26 mm. Mounting interface surfaces without electrical connector
ISO 15407-2:2003
Pneumatic fluid power. Five-port directional control valves, sizes 18 mm and 26 mm. Mounting interface surfaces with optional electrical connector
ISO/IEC 15408-1:1999
Information technology. Security techniques. Evaluation criteria for IT security. Introduction and general model
ISO/IEC 15408-2:1999
Information technology. Security techniques. Evaluation criteria for IT security. Security functional requirements
ISO/IEC 15408-3:1999
Information technology. Security techniques. Evaluation criteria for IT security. Security assurance requirements
ISO/IEC TR 15410:1998
Information technology. Telecommunications and information exchange between systems. PISN mobility-general principles and services aspects
ISO/IEC 15414:2002
Information technology. Open distributed processing. Reference model. Enterprise language
ISO/IEC 15416:2002
Information technology. Automatic identification and data capture techniques. Bar code print quality test specification. Linear symbols
ISO/IEC 15417:2000
Information technology. Automatic identification and data capture techniques. Bar code symbology specification. Code 128
ISO/IEC 15418:1999
Information technology. EAN/UCC application identifiers and fact data identifiers and maintenance
ISO/IEC 15419:2002
Information technology. Automatic identification and data capture techniques. Bar code digital imaging and printing performance testing
ISO/IEC 15420:2000
Information technology. Automatic identification and data capture techniques. Bar code symbology specification. EAN/UPC
ISO/IEC 15421:2002
Information technology. Automatic identification and data capture techniques. Bar code master test specifications
ISO/IEC 15424:2000
Information technology. Automatic identification and data capture techniques. Data Carrier Identifiers (including Symbology Identifiers)
ISO/IEC 15426-1:2000
Information technology. Automatic identification and data capture techniques. Bar code verifier conformance specifications. Linear symbols
ISO/IEC 15434:1999
Information technology. Transfer syntax for high capacity ADC media
ISO/IEC 15437:2001
Information technology. Enhancements to LOTOS (E-LOTOS)
ISO/IEC 15457-1:2001
Identification cards. Thin flexible cards. Physical characteristics
ISO/IEC 15457-2:2001
Identification cards. Thin flexible cards. Magnetic recording techniques
ISO 15459-1:1999
Information technology. Unique identification of transport units. General
ISO/IEC 15459-2:1999
Information technology. Unique identification of transport units. Registration procedures
ISO 15469:1997
Spatial distribution of daylight. CIE standard overcast sky and clear sky
ISO 15472:2001
Surface chemical analysis. X-ray photoelectron spectrometers. Calibration of energy scales
ISO/IEC 15474-1:2002
Information technology. CDIF framework. Overview
ISO/IEC 15474-2:2002
Information technology. CDIF framework. Modelling and extensibility
ISO/IEC 15475-1:2002
Information technology. CDIF transfer format. General rules for syntaxes and encodings
ISO/IEC 15475-2:2002
Information technology. CDIF transfer format. Syntax SYNTAX.1
ISO/IEC 15475-3:2002
Information technology. CDIF transfer format. Encoding ENCODING.1
ISO/IEC 15476-1:2002
Information technology. CDIF semantic metamodel. Foundation
ISO/IEC 15476-2:2002
Information technology. CDIF semantic metamodel. Common
ISO 15480:1999
Hexagon washer head drilling screws with tapping screw thread
ISO 15481:1999
Cross recessed pan head drilling screws with tapping screw thread
ISO 15482:1999
Cross recessed countersunk head drilling screws with tapping screw thread
ISO 15483:1999
Cross recessed raised countersunk head drilling screws with tapping screw thread
ISO 15487:2001
Textiles. Method for assessing appearance of apparel and other textile end products after domestic washing and drying
ISO 15489-1:2001
Information and documentation. Records management. General
ISO 15490:2000
Fine ceramics (advanced ceramics, advanced technical ceramics). Test method for tensile strength of monolithic ceramics at room temperature
ISO 15494:2003
Plastics piping systems for industrial applications. Polybutene (PB), polyethylene (PE) and polypropylene (PP). Specifications for components and the system. Metric series
ISO/IEC 15504-1:1998
Information technology. Software process assessment. Concepts and introductory guide
ISO/IEC TR 15504-2:1998
Information technology. Software process assessment. A reference model for processes and process capability
ISO/IEC TR 15504-3:1998
Information technology. Software process assessment. Performing an assessment
ISO/IEC TR 15504-4:1998
Information technology. Software process assessment. Guide to performing assessments
ISO/IEC TR 15504-5:1999
Information technology. Software process assessment. An assessment model and indicator guidance
ISO/IEC TR 15504-6:1998
Information technology. Software process assessment. Guide to competency of assessors
ISO/IEC TR 15504-7:1998
Information technology. Software process assessment. Guide for use in process improvement
ISO/IEC TR 15504-8:1998
Information technology. Software process assessment. Guide for use in determining supplier process capability
ISO/IEC TR 15504-9:1998
Information technology. Software process assessment. Vocabulary
ISO 15509:2001
Adhesives. Determination of the bond strength of engineering-plastic joints
ISO 15512:1999
Plastics. Determination of water content
ISO 15513:2000
Cranes. Competency requirements for crane drivers (operators), slingers, signallers and assessors
ISO 15528:2000
Paints, varnishes and raw materials for paints and varnishes. Sampling
ISO 15529:1999
Optics and optical instruments. Optical transfer function. Principles of measurement of modular transfer function (MTF) of sampled imaging systems
ISO 15535:2003
General requirements for establishing anthropometric databases
ISO 15540:2001
Ships and marine technology. Fire resistance of hose assemblies. Test methods
ISO 15541:2001
Ships and marine technology. Fire resistance of hose assemblies. Requirements for the test bench
ISO 15544:2000
Petroleum and natural gas industries. Offshore production installations. Requirements and guidelines for emergency response
ISO 15546:2002
Petroleum and natural gas industries. Aluminium alloy drill pipe
ISO 15547:2001
Petroleum and natural gas industries. Plate heat exchangers
ISO 15550:2002
Internal combustion engines. Determination and method for the measurement of engine power. General requirements
ISO 15554:1998
Practice for dosimetry in gamma irradiation facilities for food processing
ISO 15555:1998
Practice for use of a ceric-cerous sulfate dosimetry system
ISO 15556:1998
Guide for selection and calibration of dosimetry systems for radiation processing
ISO 15557:1998
Practice for use of a radiochromic film dosimetry system
ISO 15558:1998
Practice for use of a polymethylmethacrylate dosimetry system
ISO 15559:1998
Practice for use of a radiochromic optical waveguide dosimetry system
ISO 15560:1998
Practice for characterization and performance of a high-dose radiation dosimetry calibration laboratory
ISO 15561:1998
Practice for use of a dichromate dosimetry system
ISO 15562:1998
Practice for dosimetry in electron and bremsstrahlung irradiation facilities for food processing
ISO 15563:1998
Practice for use of the ethanol-chlorobenzene dosimetry system
ISO 15564:1998
Guide for use of radiation-sensitive indicators
ISO 15565:1998
Practice for use of a radiochromic liquid dosimetry system
ISO 15566:1998
Practice for use of the alanine-EPR dosimetry system
ISO 15567:1998
Practice for dosimetry in an X-ray (bremsstrahlung) facility for radiation processing
ISO 15568:1998
Practice for use of calorimetric dosimetry systems for electron beam dose measurements and dosimeter calibrations
ISO 15569:1998
Practice for dosimetry in an electron-beam facility for radiation processing at energies between 300 keV and 25 MeV
ISO 15570:1998
Practice for use of cellulose acetate dosimetry system
ISO 15571:1998
Practice for dosimetry in a gamma irradiation facility for radiation processing
ISO 15572:1998
Guide for estimating uncertainties in dosimetry for radiation processing
ISO 15573:1998
Practice for dosimetry in an electron-beam facility for radiation processing at energies between 80 keV and 300 keV
ISO/IEC TR 15580:2001
Information technology. Programming languages. Fortran. Floating-point exception handling
ISO/IEC TR 15581:2001
Information technology. Programming languages. Fortran. Enhanced data type facilities
ISO 15584:2001
Small craft. Inboard petrol engines. Engine-mounted fuel and electrical components
ISO 15587-1:2002
Water quality. Digestion for the determination of selected elements in water. Aqua regia digestion
ISO 15587-2:2002
Water quality. Digestion for the determination of selected elements in water. Nitric acid digestion
ISO 15592-1:2001
Fine-cut tobacco and smoking articles made from it. Methods of sampling, conditioning and analysis. Sampling
ISO 15592-2:2001
Fine-cut tobacco and smoking articles made from it. Methods of sampling, conditioning and analysis. Atmosphere for conditioning and testing
ISO 15592-3:2003
Fine-cut tobacco and smoking articles made from it. Methods of sampling, conditioning and analysis. Determination of total particulate matter of smoking articles using a routine analytical smoking machine, preparation for the determination of water and nicotine, and calculation of nicotine-free dry particulate matter
ISO 15593:2001
Environmental tobacco smoke. Estimation of its contribution to respirable suspended particles. Determination of particulate matter by ultraviolet absorbance and by fluorescence
ISO 15600:2000
Tools for moulding. Thermal insulating sheets for injection moulds
ISO 15606:2000
Dental handpieces. Air-powered scalers and scaler tips
ISO 15609-2:2001
Specification and qualification of welding procedures for metallic materials. Welding procedure specification. Gas welding
ISO 15614-8:2002
Specification and qualification of welding procedures for metallic materials. Welding procedure test. Welding of tubes to tube-plate joints
ISO 15614-11:2002
Specification and qualification of welding procedures for metallic materials. Welding procedure test. Electron and laser beam welding
ISO 15615:2002
Gas welding equipment. Acetylene manifold systems for welding, cutting and allied processes. Safety requirements in high-pressure devices
ISO 15616-1:2003
Acceptance tests for CO$d2- laser beam machines for high quality welding and cutting. General principles, acceptance conditions
ISO 15616-2:2003
Acceptance tests for CO$d2- laser beam machines for high quality welding and cutting. Measurement of static and dynamic accuracy
ISO 15616-3:2003
Acceptance tests for CO$d2- laser beam machines for high quality welding and cutting. Calibration of instruments for measurement of gas flow and pressure
ISO 15618-1:2002
Qualification testing of welders for under-water welding. Diver-welders for hyperbaric wet welding
ISO 15618-2:2002
Qualification testing of welders for under-water welding. Diver-welders and welding operators for hyperbaric dry welding
ISO 15620:2000
Welding. Friction welding of metallic materials
ISO 15621:1999
Urine-absorbing aids. General guidance on evaluation
ISO 15629:2002
Pallets for materials handling. Quality of fasteners for assembly of new and repair of used, flat, wooden pallets
ISO 15630-1:2002
Steel for the reinforcement and prestressing of concrete. Test methods. Reinforcing bars, wire rod and wire
ISO 15630-2:2002
Steel for the reinforcement and prestressing of concrete. Test methods. Welded fabric
ISO 15630-3:2002
Steel for the reinforcement and prestressing of concrete. Test methods. Prestressing steel
ISO 15632:2002
Microbeam analysis. Instrumental specification for energy dispersive X-ray spectrometers with semiconductor detectors
ISO 15637-1:2002
Holding fixtures of cylindrical abrasive sleeves. Holding fixtures with shank for hand-held grinding machines
ISO 15637-2:2002
Holding fixtures of cylindrical abrasive sleeves. Holding fixtures for stationary machines
ISO 15641:2001
Milling cutters for high speed machining. Safety requirements
ISO 15643:2002
Road construction and maintenance equipment. Bituminous binder spreaders/sprayers. Terminology and commercial specifications
ISO 15644:2002
Road construction and maintenance equipment. Chippings spreaders. Terminology and commercial specifications
ISO 15645:2002
Road construction and maintenance equipment. Road milling machinery. Terminology and commercial specifications
ISO 15649:2001
Petroleum and natural gas industries. Piping
ISO 15663-1:2000
Petroleum and natural gas industries. Life cycle costing. Methodology
ISO 15663-2:2001
Petroleum and natural gas industries. Life cycle costing. Guidance on application of methodology and calculation methods
ISO 15663-3:2001
Petroleum and natural gas industries. Life cycle costing. Implementation guidelines
ISO 15664:2001
Acoustics. Noise control design procedures for open plant
ISO 15665:2003
Acoustics. Acoustic insulation for pipes, valves and flanges
ISO 15667:2000
Acoustics. Guidelines for noise control by enclosures and cabins
ISO 15668:1999
Banking. Secure file transfer (retail)
ISO 15671:2000
Rubber and rubber additives. Determination of total sulfur content using an automatic analyser
ISO 15672:2000
Rubber and rubber additives. Determination of total nitrogen content using an automatic analyser
ISO 15674:2001
Cardiovascular implants and artificial organs. Hard-shell cardiotomy/venous reservoir systems (with/without filter) and soft venous reservoir bags
ISO 15675:2001
Cardiovascular implants and artificial organs. Cardiopulmonary bypass systems. Arterial line blood filters
ISO 15682:2001
Water quality. Determination of chloride by flow analysis (CFA and FIA) and photometric or potentiometric detection
ISO 15686-1:2000
Buildings and constructed assets. Service life planning. General principles
ISO 15686-2:2001
Buildings and constructed assets. Service life planning. Service life prediction procedures
ISO 15686-3:2002
Buildings and constructed assets. Service life planning. Performance audits and reviews
ISO/IEC 15693-1:2000
Identification cards. Contactless integrated circuit(s) cards. Vicinity cards. Physical characteristics
ISO/IEC 15693-2:2000
Identification cards. Contactless integrated circuit(s) cards. Vicinity cards. Air interface and initialization
ISO/IEC 15693-3:2001
Identification cards. Contactless integrated circuit(s) cards. Vicinity cards. Anticollision and transmission protocol
ISO 15695:2001
Vitreous and porcelain enamels. Determination of scratch resistance of enamel finishes
ISO 15700:1999
Leather. Tests for colour fastness. Colour fastness to water spotting
ISO 15701:1999
Leather. Tests for colour fastness. Colour fastness to migration into plasticized poly (vinyl chloride)
ISO 15702:2000
Leather. Tests for colour fastness. Colour fastness to machine washing
ISO 15703:1999
Leather. Tests for colour fastness. Colour fastness to mild washing
ISO 15705:2002
Water quality. Determination of the chemical oxygen demand index (ST-COD). Small-scale sealed-tube method
ISO 15706:2002
Information and documentation. International Standard Audiovisual Number (ISAN)
ISO 15707:2001
Information and documentation. International standard musical work code (ISWC)
ISO 15710:2002
Paints and varnishes. Corrosion testing by alternate immersion in and removal from a buffered sodium chloride solution
ISO 15715:2003
Binders for paints and varnishes. Determination of turbidity
ISO 15720:2001
Metallic coatings. Porosity tests. Porosity in gold or palladium coatings on metal substrates by gel-bulk electrography
ISO 15721:2001
Metallic coatings. Porosity tests. Porosity in gold or palladium coatings by sulfurous acid/sulfur dioxide vapour
ISO 15724:2001
Metallic and other inorganic coatings. Electrochemical measurement of diffusible hydrogen in steels. Barnacle electrode method
ISO 15730:2000
Metallic and other inorganic coatings. Electropolishing as a means of smoothing and passivating stainless steel
ISO 15734:2001
Ships and marine technology. Hydrostatic release units
ISO 15738:2002
Ships and marine technology. Gas inflation systems for inflatable life-saving appliances
ISO 15739:2003
Photography. Electronic still-picture imaging. Noise measurements
ISO 15741:2001
Paints and varnishes. Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases
ISO 15744:2002
Hand-held non-electric power tools. Noise measurement code. Engineering method (grade 2)
ISO 15748-1:2002
Ships and marine technology. Potable water supply on ships and marine structures. Planning and design
ISO 15748-2:2002
Ships and marine technology. Potable water supply on ships and marine structures. Method of calculation
ISO 15750-1:2002
Packaging. Steel drums. Removable head (open head) drums with a minimum total capacity of 208 l, 210 l and 216,5 l
ISO 15750-2:2002
Packaging. Steel drums. Non-removable head (tight head) drums with a minimum total capacity of 121 l, 216,5 l and 230 l
ISO 15750-3:2002
Packaging. Steel drums. Inserted flange-type closure systems
ISO 15752:2000
Ophthalmic instruments. Endoilluminators. Fundamental requirements and test methods for optical radiation safety
ISO 15755:2000
Paper and board. Estimation of contraries
ISO 15761:2002
Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries
ISO 15767:2003
Workplace atmospheres. Controlling and characterizing errors in weighing collected aerosols
ISO/TS 15768:2000
Measurement of liquid velocity in open channels. Design, selection and use of electromagnetic current meters
ISO/TS 15769:2000
Hydrometric determination. Liquid flow in open channels and partly filled pipes. Guidelines for the application of Doppler-based flow measurements
ISO/IEC 15773:1998
Information technology. Telecommunications and information exchange between systems. Broadband private integrated services network. Inter-exchange signalling protocol. Transit counter additional network feature
ISO 15774:2001
Animal and vegetable fats and oils. Determination of cadmium content by direct graphite furnace atomic absorption spectrometry
ISO 15783:2003
Seal-less rotodynamic pumps. Class II. Specification
ISO 15785:2002
Technical drawings. Symbolic presentation and indication of adhesive fold and pressed joints
ISO 15788-1:2001
Animal and vegetable fats and oils. Determination of stigmastadienes in vegetable oils. Method using capillary-column gas chromatography (Reference method)
ISO 15791-1:2002
Plastics. Development and use of intermediate-scale fire tests for plastics products. General guidance
ISO 15794:2001
Bi-directional and multi-directional fork-lift trucks. Stability tests
ISO 15795:2002
Optics and optical instruments. Quality evaluation of optical systems. Assessing the image quality degradation due to chromatic aberrations
ISO 15797:2002
Textiles. Industrial washing and finishing procedures for testing of workwear
ISO 15798:2001
Ophthalmic implants. Ophthalmic viscosurgical devices
ISO/IEC 15802-1:1995
Information technology. Telecommunications and information exchange between systems. Local and metropolitan area networks - common specifications. Medium Access Control (MAC) service definition
ISO/IEC 15802-2:1995
Information technology. Telecommunications and information exchange between systems. Local and metropolitan area networks - common specifications. LAN/MAN management
ISO/IEC 15802-4:1994
Information technology. Telecommunications and information exchange between systems. Local and metropolitan area networks - common specifications. System load protocol
ISO/IEC 15802-5:1998
Information technology. Telecommunications and information exchange between systems. Local and metropolitan area networks - common specifications. Remote media access control (MAC) bridging
ISO/IEC TR 15846:1998
Information technology. Software life cycle processes. Configuration management
ISO 15849:2001
Ships and marine technology. Guidelines for implementation of a fleet management system network
ISO 15850:2002
Plastics. Determination of tension-tension fatigue crack propagation. Linear elastic fracture mechanics (LEFM) approach
ISO/IEC 15852:1999
Information technology. Programming languages. M Windowing API
ISO 15870:2000
Powered industrial trucks. Safety signs and hazard pictorials. General principles
ISO 15871:2000
Industrial trucks. Specification for indicator lights for container handling and grappler arm operations
ISO 15872:2002
Aerospace. UNJ threads. Gauging
ISO 15882:2003
Sterilization of health care products. Chemical indicators. Guidance for selection, use and interpretation of results
ISO 15884:2002
Milk fat. Preparation of fatty acid methyl esters
ISO 15889:2003
Space data and information transfer systems. Data description language. EAST specification
ISO/IEC 15897:1999
Information technology. Procedures for registration of cultural elements
ISO/IEC 15899:1998
Information technology. Telecommunications and information exchange between systems. Broadband private integrated services network. Service description. Broadband connection oriented bearer services
ISO 15903:2002
Soil quality. Format for recording soil and site information
ISO 15908:2002
Adhesives for thermoplastic piping systems. Test method for the determination of thermal stability of adhesives
ISO/IEC 15910:1999
Information technology. Software user documentation process
ISO 15911:2000
Methods of test for petroleum and its products. Estimation of net specific energy of aviation turbine fuels using hydrogen content data
ISO 15913:2003
Water quality. Determination of selected phenoxyalkanoic herbicides, including bentazones and hydroxybenzonitriles by gas chromatography and mass spectrometry after solid phase extraction and derivatization
ISO 15929:2002
Graphic technology. Prepress digital data exchange. Guidelines and principles for the development of PDF/X standards
ISO 15930-1:2001
Graphic technology. Prepress digital data exchange. Use of PDF. Complete exchange using CMYK data (PDF/X-1) and PDF/X-1a)
ISO/IEC 15939:2002
Software engineering. Software measurement process
ISO/IEC TR 15942:2000
Information technology. Programming languages. Guide for the use of the Ada programming language in high integrity systems
ISO/IEC 15944-1:2002
Information technology. Business agreement semantic descriptive techniques. Operational aspects of Open-edi for implementation
ISO/IEC 15945:2002
Information technology. Security techniques. Specification of TTP services to support the application of digital signatures
ISO/IEC 15946-1:2002
Information technology. Security techniques. Cryptographic techniques based on elliptic curves. General
ISO/IEC 15946-2:2002
Information technology. Security techniques. Cryptographic techniques based on elliptic curves. Digital signatures
ISO/IEC 15946-3:2002
Information technology. Security techniques. Cryptographic techniques based on elliptic curves. Key establishment
ISO/IEC TR 15947:2002
Information technology. Security techniques. IT intrusion detection framework
DD ISO/TR 15969:2001
Surface chemical analysis. Depth profiling. Measurement of sputtered depth
ISO 15973:2001
Closed and blind rivets with break pull mandrel and protruding head. AIA/St
ISO 15974:2001
Closed and blind rivets with break pull mandrel and countersunk head. AIA/St
ISO 15975:2002
Closed end blind rivets with break pull mandrel and protruding head. AI/AIA
ISO 15976:2002
Closed end blind rivets with break pull mandrel and protruding head. St/St
ISO 15977:2002
Open end blind rivets with break pull mandrel and protruding head. AIA/St
ISO 15978:2002
Open end blind rivets with break pull mandrel and countersunk head. AIA/St
ISO 15979:2002
Open end blind rivets with break pull mandrel and protruding head. St/St
ISO 15980:2002
Open end blind rivets with break pull mandrel and countersunk head. St/St
ISO 15981:2002
Open end blind rivets with break pull mandrel and protruding head. AIA/AIA
ISO 15982:2002
Open end blind rivets with break pull mandrel and countersunk head. AIA/AIA
ISO 15983:2002
Open end blind rivets with break pull mandrel and protruding head. A2/A2
ISO 15984:2002
Open end blind rivets with break pull mandrel and countersunk head. A2/A2
ISO 15987:2003
Plastics. Film and sheeting. Biaxially oriented polyamide (nylon) films
ISO 15988:2003
Plastics. Film and sheeting. Biaxially oriented poly(ethylene terephthalate) (PET) films
ISO 16000-3:2001
Indoor air. Determination of formaldehyde and other carbonyl compounds. Active sampling method
ISO 16014-1:2003
Plastics. Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography. General principles
ISO 16014-2:2003
Plastics. Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography. Universal calibration method
ISO 16014-3:2003
Plastics. Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography. Low-temperature method
ISO 16014-4:2003
Plastics. Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography. High-temperature method
ISO 16016:2000
Technical product documentation. Protection notices for restricting the use of documents and products
ISO 16017-1:2001
Indoor, ambient and workplace air. Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography. Pumped sampling
ISO 16017-2:2003
Indoor, ambient and workplace air. Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography. Diffusive sampling
ISO 16021:2001
Urine-absorbing aids. Basic principles for evaluation of single-use adult-incontinence-absorbing aids from the perspective of users and caregivers
ISO/IEC 16022:2000
Information technology. International symbology specification. Data matrix
ISO/IEC 16023:2000
Information technology. International symbology specification. Maxicode
ISO 16028:1999
Hydraulic fluid power. Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar). Specifications
ISO 16030:2001
Pneumatic fluid power. Connections. Ports and stud ends
ISO 16035:2003
Animal and vegetable fats and oils. Determination of low-boiling halogenated hydrocarbons in edible oils
ISO 16048:2003
Passivation of corrosion-resistant stainless-steel fasteners
ISO 16049-1:2001
Air cargo equipment. Restraint straps. Design criteria and testing methods
ISO 16054:2002
Implants for surgery. Minimum data sets for surgical implants
ISO 16057:2002
Coated abrasives. Vulcanized fibre discs
ISO 16063-1:1998
Methods for the calibration of vibration and shock transducers. Basic concepts
ISO 16063-11:1999
Methods for the calibration of vibration and shock transducers. Primary vibration calibration by laser interferometry
ISO 16063-12:2002
Methods for the calibration of vibration and shock transducers. Primary vibration calibration by the reciprocity method
ISO 16063-13:2001
Methods for the calibration of vibration and shock transducers. Primary shock calibration using laser interferometry
ISO 16063-21:2003
Methods for the calibration of vibration and shock transducers. Vibration calibration by comparison to a reference transducer
ISO 16065-1:2001
Pulps. Determination of fibre length by automated optical analysis. Polarized light method
ISO 16070:2002
Petroleum and natural gas industries. Downhole equipment. Lock mandrels and landing nipples
ISO 16072:2002
Soil quality. Laboratory methods for determination of microbial soil respiration
ISO 16091:2002
Space systems. Integrated logistic support
ISO 16104:2003
Packaging. Transport packaging for dangerous goods. Test methods
ISO 16107:1999
Workplace atmospheres. Protocol for evaluating the performance of diffusive samplers
ISO 16140:2003
Microbiology of food and animal feeding stuffs. Protocol for the validation of alternative methods
DD ISO/TR 16144:2002
Hydraulic fluid power. Calibration of liquid automatic particle counters. Procedures used to certify the standard reference material SRM 2806
ISO 16147:2002
Small craft. Inboard diesel engines. Engine-mounted fuel and electrical components
ISO 16165:2001
Ships and marine technology. Marine environment protection. Terminology relating to oil spill response
ISO 16221:2001
Water Quality. Guidance for determination of biodegradability in the marine environment
ISO/IEC 16262:2002
Information technology. ECMAScript language specification
ISO 16264:2002
Water quality. Determination of soluble silicates by flow analysis (FIA and CFA) and photometric detection
ISO 16284:2001
Ophthalmic optics. Information interchange for ophthalmic optical equipment
ISO/IEC 16326:1999
Software engineering. Guide for the application of ISO/IEC 12207 to project management
ISO 16329:2003
Ships and marine technology. Heading control systems for high-speed craft
ISO 16330:2003
Reciprocating positive displacement pumps and pump units. Technical requirements
ISO 16348:2003
Metallic and other inorganic coatings. Definitions and conventions concerning appearance
ISO 16366:2001
Tools for pressing. L-shaped guides
ISO 16367:2001
Tools for pressing. Guide plates. U- and V-blocks
ISO/TR 16386:1999
Impact of changes in ISO fluid power particle counting. Contamination control and filter test standards
ISO/IEC 16388:1999
Information technology. Automatic identification and data capture techniques. Bar code symbology specifications. Code 39
ISO/IEC 16390:1999
Information technology. Automatic identification and data capture techniques. Bar code symbology specifications. Interleaved 2 of 5
ISO 16426:2002
Fasteners. Quality assurance system
ISO 16446:2002
Ships and marine technology. Marine environmental protection. Adaptor for joining dissimilar boom connectors
ISO 16565:2002
Rubber. Determination of 5-ethylidenenorbornene (ENB) or dicyclopentadiene (DCPD) in ethylene-propylene-diene (EPDM) terpolymers
ISO 16582:2002
Open end blind rivets with break pull mandrel and protruding head. Cu/St or Cu/Br or Cu/SSt
ISO 16583:2002
Open end blind rivets with break pull mandrel and countersunk head. Cu/St or Cu/Br or Cu/SSt
ISO 16584:2002
Open end blind rivets with break pull mandrel and protruding head. NiCu/St or NiCu/SSt
ISO 16585:2002
Closed end blind rivets with pull mandrel and protruding head. A2/SSt
ISO 16588:2002
Water quality. Determination of six complexing agents. Gas-chromatographic method
ISO 16589-1:2001
Rotary shaft lip-type seals incorporating thermoplastic sealing elements. Nominal dimensions and tolerances
ISO 16589-2:2001
Rotary shaft lip-type seals incorporating thermoplastic sealing elements. Vocabulary
ISO 16589-3:2001
Rotary shaft lip-type seals incorporating thermoplastic sealing elements. Storage, handling and installation
ISO 16589-4:2001
Rotary shaft lip-type seals incorporating thermoplastic sealing elements. Performance test procedures
ISO 16589-5:2001
Rotary shaft lip-type seals incorporating thermoplastic sealing elements. Identification of visual imperfections
DD ISO/TS 16628:2003
Tracheobronchial tubes. Recommendations for size designation and labelling
ISO 16649-1:2001
Microbiology of food and animal feeding stuffs. Horizontal method for the enumeration of $Gb-glucuronidase-positive $7IEscherichia coli$7R. Colony-count technique at 44$0DC using membranes and 5-bromo-4- chloro-3-indolyl-$Gb-D-glucuronide
ISO 16649-2:2001
Microbiology of food and animal feeding stuffs. Horizontal method for the enumeration of $Gb-glucuronidase-positive $7IEscherichia coli$7R. Colony-count technique at 44$0DC using 5-bromo-4-chloro-3-indolyl-$Gb-D-glucuronide
ISO 16654:2001
Microbiology of food and animal feeding stuffs. Horizontal method for the detection of $7IEscherichia coli$7R O157
ISO 16663-1:2003
Fishing nets. Method of test for the determination of mesh size. Opening of mesh
ISO 16663-2:2003
Fishing nets. Method of test for the determination of mesh size. Length of mesh
DD ISO/TS 16668:2000
Basic semantics register (BSR)
ISO 16672:2003
Ophthalmic implants. Ocular endotamponades
ISO 16702:2001
Workplace air quality. Determination of total isocyanate groups in air using 2-(1-methoxyphenyl) piperazine and liquid chromatography
ISO/TS 16799:1999
Rolling bearings. Dynamic load ratings and rating life. Discontinuities in the calculating of basic dynamic load ratings
ISO 16869:2001
Plastics. Assessment of the effectiveness of fungistatic compounds in plastics formulations
ISO 16871:2003
Plastics piping and ducting systems. Plastics pipes and fittings. Method for exposure to direct (natural) weathering
ISO 16873:2002
Hydraulic fluid power. Pressure switches. Mounting surfaces
ISO 16889:1999
Hydraulic fluid power filters. Multi-pass method for evaluating filtration performance of a filter element
ISO 16902-1:2003
Hydraulic fluid power. Test code for the determination of sound power levels using sound intensity techniques. Engineering method. Pumps
ISO/TS 16922:2002
Natural gas. Guidelines for odorizing gases
ISO 16929:2002
Plastics. Determination of the degree of disintegration of plastic materials under defined composting conditions in a pilot-scale test
ISO 16931:2001
Animal and vegetable fats and oils. Determination of polymerized triglycerides content by high performance size-exclusion chromatography (HPSEC)
ISO/IEC 17024:2003
Conformity Assessment. General requirements for bodies operating certification of persons
ISO/IEC 17025:2000
General requirements for the competence of testing and calibration laboratories
DD ISO/TS 17090-1:2002
Health informatics. Public key infrastructure. Framework and overview
DD ISO/TS 17090-2:2002
Health informatics. Public key infrastructure. Certificate profile
DD ISO/TS 17090-3:2002
Health informatics. Public key infrastructure. Policy management of certification authority
DD ISO/TS 17117:2002
Health informatics. Controlled health terminology. Structure and high-level indicators
ISO 17155:2002
Soil quality. Determination of abundance and activity of soil microflora using respiration curves
ISO 17166:1999
Erythema reference action spectrum and standard erythema dose
ISO 17186:2002
Leather. Physical and mechanical tests. Determination of surface coating thickness
ISO 17202:2002
Textiles. Determination of twist in single spun yarns. Untwist/retwist method
DD CEN ISO/TS 17226:2003
Leather. Chemical tests. Determination of formaldehyde content
ISO 17227:2002
Leather. Physical and mechanical tests. Determination of dry heat resistance of leather
ISO 17229:2002
Leather. Physical and mechanical tests. Determination of water vapour absorption
ISO 17233:2002
Leather. Physical and mechanical tests. Determination of cold crack temperature of surface coatings
DD CEN ISO/TS 17234:2003
Leather. Chemical tests. Determination of certain azo colourants in dyed leathers
ISO 17235:2002
Leather. Physical and mechanical tests. Determination of softness
ISO 17236:2002
Leather. Physical and mechanical tests. Determination of extension set
DD CEN ISO/TS 17262:2003
Automatic vehicle and equipment identification. Intermodal goods transport. Numbering and data structures
DD CEN ISO/TS 17263:2003
Automatic vehicle and equipment identification. Intermodal goods transport. System parameters
ISO 17266:2002
Cinematography. Multichannel analogue and digital photographic sound and control records on 35 mm motion-picture prints and negatives, and digital sound-control records on 70 mm motion-picture prints and negatives. Position and width dimensions
ISO 17281:2002
Plastics. Determination of fracture toughness ($iG$di$dc and $iK$di$dc) at moderately high loading rates (1 m/s)
ISO 17287:2003
Road vehicles. Ergonomic aspects of transport information and control systems. Procedure for assessing suitability for use while driving
ISO 17288-1:2002
Passenger cars. Free-steer behaviour. Steering-release open-loop test method
ISO 17332:2001
Cinematography. Manufacturer printed latent image identification information for 35mm motion-picture colour-print film. Specifications
ISO 17339:2002
Ships and marine technology. Sea anchors for survival craft and rescue boats
ISO 17355:2003
Space data and information transfer systems. CCSDS file delivery protocol
ISO 17357:2002
Ships and marine technology. High-pressure floating pneumatic rubber fenders
ISO 17410:2001
Microbiology of food and animal feeding stuffs. Horizontal method for the enumeration of psychrotrophic micro-organisms
ISO 17422:2002
Plastics. Environmental aspects. General guidelines for their inclusion in standards
ISO 17433:2003
Space data and information transfer systems. Packet telemetry services
ISO 17493:2000
Clothing and equipment for protection against heat. Test method for convective heat resistance using a hot air circulating oven
ISO 17495:2003
Water quality. Determination of selected nitrophenols. Method by solid-phase extraction and gas chromatography with mass spectrometric detection
ISO 17510-1:2002
Sleep apnoea breathing therapy. Sleep apnoea breathing therapy devices
ISO 17510-2:2003
Sleep apnoea breathing therapy. Masks and application accessories
ISO 17511:2003
In vitro diagnostic medical devices. Measurement of quantities in biological samples. Metrological traceability of values assigned to calibrators and control materials
ISO 17526:2003
Optics and optical instruments. Lasers and laser-related equipment. Lifetime of lasers
ISO 17531:2002
Photography. Processing chemicals. Specifications for 4-(N-ethyl-N-2- methanesulfonylaminoethyl)-2-methylphenylenediamine sesquisulfate monohydrate
ISO 17560:2002
Surface chemical analysis. Secondary-ion mass spectrometry. Method for depth profiling of boron in silicon
ISO 17564:2001
Nitrile rubber. Determination of residual unsaturation in hydrogenated nitrile rubber (HNBR) by iodine value
DD CEN ISO/TS 17573:2003
Road transport and traffic telematics. Electronic fee collection (EFC). System architecture for vehicle related transport services
ISO 17631:2002
Ships and marine technology. Shipboard plans for fire protection, life-saving appliances and means of escape
ISO 17652-1:2003
Welding. Test for shop primers in relation to welding and allied processes. General requirements
ISO 17652-2:2003
Welding. Test for shop primers in relation to welding and allied processes. Welding properties of shop primers
ISO 17652-3:2003
Welding. Test for shop primers in relation to welding and allied processes. Thermal cutting
ISO 17652-4:2003
Welding. Test for shop primers in relation to welding and allied processes. Emission of fumes and gases
ISO 17653:2003
Destructive tests on welds in metallic materials. Torsion test of resistance spot welds
ISO 17654:2003
Destructive tests on welds in metallic materials. Resistance welding. Pressure test on resistance seam welds
ISO 17655:2003
Destructive tests on welds in metallic materials. Method for taking samples for delta ferrite measurement
ISO 17666:2003
Space systems. Risk management
ISO 17710:2002
Plastics. Polyols for use in the production of polyurethane. Determination of degree of unsaturation by microtitration
ISO 17724:2003
Graphical symbols. Vocabulary
DD ISO/TS 17764-1:2002
Animal feeding stuffs. Determination of the content of fatty acids. Preparation of methyl esters
ISO 17771:2003
Plastics. Thermoset moulding compounds. Determination of the degree of fibre wetting in SMC
ISO 17776:2002
Petroleum and natural gas industries. Offshore production installations. Guidance on tools and techniques for hazard identification and risk assessment
ISO/IEC 17799:2000
Information technology. Code of practice for information security management
ISO 17900:2002
Agricultural trailers. Balanced and semi-mounted trailers. Determination of payload, vertical static load and axle load
ISO 17973:2002
Surface chemical analysis. Medium-resolution Auger electron spectrometers. Calibration of energy scales for elemental analysis
ISO 17974:2002
Surface chemical analysis. High-resolution Auger electron spectrometers. Calibration of energy scales for elemental and chemical-state analysis
ISO/PAS 17984:2001
Machine-made textile floor coverings. Determination of dimensional changes after exposure to heat and/or water
ISO 17993:2002
Water quality. Determination of 15 polycyclic aromatic hydrocarbons (PAH) in water by HPLC with fluorescence detection after liquid-liquid extraction
ISO/IEC 18004:2000
Information technology. Automatic identification and data capture techniques. Bar code symbology. QR Code
ISO/IEC 18009:1999
Information technology. Programming languages. Ada: conformity assessment of a language processor
ISO/IEC 18014-1:2002
Information technology. Security techniques. Time-stamping services. Framework
ISO/IEC 18014-2:2002
Information technology. Security techniques. Time-stamping services. Mechanisms producing independent tokens
ISO 18114:2003
Surface chemical analysis. Secondary-ion mass spectrometry. Determination of relative sensitivity factors from ion-implanted reference materials
ISO 18115:2001
Surface chemical analysis. Vocabulary
ISO 18153:2003
In vitro diagnostic medical devices. Measurement of quantities in biological samples. Metrological traceability of values for catalytic concentration of enzymes assigned to calibrators and control materials
ISO 18165:2001
Petroleum and natural gas industries. Performance testing of cementing float equipment
ISO 18330:2003
Milk and milk products. Guidelines for the standardized description of immunoassays or receptor assays for the detection of antimicrobial residues
ISO 18333:2002
Pallets for materials handling. Quality of new wooden components for flat pallets
ISO 18334:2003
Pallets for materials handling. Quality of assembly of new, wooden, flat pallets
ISO 18413:2002
Hydraulic fluid power. Cleanliness of parts and components. Inspection document and principles related to contaminant collection, analysis and data reporting
ISO 18553:2002
Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds
ISO 18609:2001
Animal and vegetable fats and oils. Determination of unsaponifiable matter. Method using hexane extraction
ISO 18738:2003
Lifts (elevators). Measurement of lift ride quality
ISO 18812:2003
Health informatics. Clinical analyser interfaces to laboratory information systems. Use profiles
ISO 18901:2002
Imaging materials. Processed silver-gelatin type black-and-white film. Specifications for stability
ISO 18902:2001
Imaging materials. Processed photographic films, plates and papers. Filing enclosures and storage containers
ISO 18903:2002
Imaging materials. Films and paper. Determination of dimensional change
ISO 18904:2000
Imaging materials. Processed films. Method for determining lubrication
ISO 18905:2002
Imaging materials. Ammonia-processed diazo photographic film. Specifications for stability
ISO 18906:2000
Imaging materials. Photographic films. Specifications for safety film
ISO 18907:2000
Imaging materials. Photographic films and papers. Wedge test for brittleness
ISO 18908:2000
Imaging materials. Photographic film. Determination of folding endurance
ISO 18910:2000
Imaging materials. Photographic film and paper. Determination of curl
ISO 18911:2000
Photography. Processed safety photographic films. Storage practices
ISO 18912:2002
Imaging materials. Processed vesicular photographic film. Specifications for stability
ISO 18914:2002
Imaging materials. Photographic film and papers. Method for determining the resistance of photographic emulsions to wet abrasion
ISO 18915:2000
Imaging materials. Methods for the evaluation of the effectiveness of chemical conversion of silver images against oxidation
ISO 18917:1999
Photography. Determination of residual thiosulfate and other related chemicals in processed photographic materials. Methods using iodine-amylose, methylene blue and silver sulfide
ISO 18918:2000
Imaging materials. Processed photographic plates. Storage practices
ISO 18919:1999
Photography. Thermally processed silver microfilm. Specifications for stability
ISO 18920:2000
Imaging materials. Processed photographic reflection prints. Storage practices
ISO 18921:2002
Imaging materials. Compact discs (CD-ROM). Method for estimating the life expectancy based on the effects of temperature and relative humidity
ISO 18922:2003
Imaging materials. Processed photographic films. Methods for determining scratch resistance
ISO 18923:2000
Imaging materials. Polyester-base magnetic tape. Storage practices
ISO 18924:2000
Imaging materials. Test methods for Arrhenius type predictions
ISO 18925:2002
Imaging materials. Optical disk media. Storage practices
ISO 18927:2002
Imaging materials. Recordable compact disc systems. Method for estimating the life expectancy based on the effects of temperature and relative humidity
ISO 18928:2002
Imaging materials. Unprocessed photographic films and papers. Storage practices
ISO 19011:2002
Guidelines for quality and/or environmental management systems auditing
ISO 19011:2002 (A5 Laminated)
Guidelines for quality and/or environmental management systems auditing. A5 laminated edition
ISO 19101:2002
Geographic information. Reference model
ISO 19105:2000
Geographic information. Conformance and testing
ISO 19107:2003
Geographic information. Spatial schema
ISO 19108:2002
Geographic information. Temporal schema
ISO 19111:2003
Geographic information. Spatial referencing by coordinates
ISO 19113:2002
Geographic information. Quality principles
ISO 19115:2003
Geographic information. Metadata
ISO/TR 19121:2000
Geographic information. Imagery and gridded data
ISO 19219:2002
Animal and vegetable fats and oils. Determination of visible foots in crude fats and oils
ISO 19378:2003
Lubricants, industrial oils and related products (class L). Machine-tool lubricants. Categories and specifications
ISO/IEC 19500-2:2003
Information technology. Open distributed processing. General Inter-ORB Protocol (GIOP)/Internet Inter-ORB Protocol (IIOP)
ISO/IEC 19761:2003
Software engineering. COSMIC-FFP. A functional size measurement method
ISO 19900:2002
Petroleum and natural gas industries. General requiremenents for offshore structures
ISO 19901-4:2003
Petroleum and natural gas industries. Specific requirements for offshore structures. Geotechnical and foundation design considerations
ISO 19901-5:2003
Petroleum and natural gas industries. Specific requirements for offshore structures. Weight control during engineering and construction
ISO 20000:2005
IT Service Management (ref BS15000). Ref: ISO 20000 User Group
ISO/IEC 20060:2001
Information technology. Open terminal architecture (OTA) specification. Virtual machine specification
ISO 20341:2003
Surface chemical analysis. Secondary-ion mass spectrometry. Method for estimating depth resolution parameters with multiple delta-layer reference materials
ISO 20482:2003
Metallic materials. Sheet and strip. Erichsen cupping test
ISO 20823:2003
Petroleum and related products. Determination of the flammability characteristics of fluids in contact with hot surfaces. Manifold ignition test
ISO/IEC 20968:2002
Software engineering. Mk II function point analysis. Counting practices manual
ISO/IEC 20970:2002
Information technology. Programming languages, their environments and system software interfaces. JEFF file format
ISO 21147:2003
Fine-cut tobacco and smoking articles made from it. Survey and analysis of consumer-made articles
ISO 21227-1:2003
Paints and varnishes. Evaluation of defects on coated surfaces using optical imaging. General guidance
ISO 21533:2003
Dentistry. Reusable cartridge syringes intended for intraligamentary injections
ISO 21961:2003
Space data and information transfer systems. Data entity dictionary specification language (DEDSL). Abstract syntax
ISO 21962:2003
Aerospace series. Space data and information transfer systems. Data entity dictionary specification language (DEDSL). PVL syntax
ISO 22628:2002
Road vehicles. Recyclability and recoverability. Calculation method
ISO 22643:2003
Space data and information transfer systems. Data entity dictionary specification language (DEDSL). XML/DTD Syntax
ISO/IEC 23270:2003
Information technology. C# Language Specification
ISO 25539-1:2003
Cardiovascular implants. Endovascular devices. Endovascular prostheses
ISO 27001:2005
Information Security Management System (ISMS). Ref: ISO 27001 Online. Part of new ISO 27000 series.
ISO 81714-1:2001
Design of graphical symbols for use in the technical documentation of products. Basic rules
DD ISO/TS 15666:2003
Acoustics. Assessment of noise annoyance by means of social and socio-acoustic surveys
| 
